Search - Ice Cold Beer Manual

Servo Alignment Procedure

MAINTENANCE » Servo Alignment Procedure

1) Remove Glass & Back door 2) Disconnect both screw drive motors from back LED board 3) Power on game, servo should cycle from Ball gate to return hole and back to Ball gate 4) Connect to game with the Ice Cold Beer app 5) Select Calibration then select Servo …

Servo Disc Alignment Procedure

MAINTENANCE » Servo Alignment Procedure » Servo Disc Alignment Procedure

1) Power Game off then back on again. Servo motor should cycle to Return Hole than back to gate hole. 2) unplug servo unit and remove from playfield 3) Remove Allen screw (2.5 mm) holding disc to motor 4) Remove disc from assembly and rotate so slot in disc lines up…

“ICE COLD BEER” GAME SET-UP

Bar Self-Test and Manual Testing

“ICE COLD BEER” GAME SET-UP » Initial Testing Procedures » Bar Self-Test and Manual Testing

Bar Self-Test To initiate the bar self-test, move a joystick in any direction. During the self-test: The bar will descend to retrieve the ball. The ball will be cycled into a scoring hole. The ball will return to the gate, and the bar will move to the top of the…

Replacing Servo Assembly with new unit

MAINTENANCE » Servo Alignment Procedure » Replacing Servo Assembly with new unit

Early Production models used Back LED board Version v4.0, Later models used v4.1 The connector on the LED board for the servo assembly is wired differently between the two versions. Version v4.0 servo connector is wired 5V-TX-GND Version v4.1 servo connector…

Game Settings

“ICE COLD BEER” GAME SET-UP » Dip Switch Settings » Game Settings

Here you can select ICB Coin Op for coin operated play or Freeplay (Zeke’s peak is coming soon!) If you select “ICB Coin Op”, you may also select the number of coins required to start a game under “Coinage” (Selection between a one and…

Screw drive lubrication

MAINTENANCE » Lubrication Of Mechanical Parts » Screw drive lubrication

Every 2-4 weeks in a high use environment or 3-6 months in home use the screw drives in the back of the machine should be lubricated. (if you have brass shavings and screw drive wear, clean and do this immediately) Remove the back door Put a 1/2” to 1”…

Stepper Motor Current Adjustment

MAINTENANCE » Stepper Motor Current Adjustment

Stepper Motor Current adjustment procedure Remove the top Bar holding glass in place and carefully remove the glass Remove the two square head screws under the marquee light Pull top of the Playfield forward and insert OLED screen as shown and power on game #…

Bar / Ball gate adjustment

MAINTENANCE » Bar / Ball gate adjustment

If Game Ball is not coming out of Gate hole or if ball is hitting glass when it rolls out of gate. Remove back door Facing back of game locate aluminum block attached to screw drive on the right hand side. loosen screws holding adjustment tab to aluminum block and…

Introduction

“ICE COLD BEER” GAME SET-UP » Introduction

Retro Arcade LLC is pleased to re-introduce Taito’s “ICE COLD BEER“™ , a celebrated remake of this arcade icon. The object of the game is for the player to maneuver the ball with the joysticks that moves the bar to position the ball in the lit hole.…

Initial Testing Procedures

“ICE COLD BEER” GAME SET-UP » Initial Testing Procedures

Initial Testing Procedures The following testing procedures ensure your Ice Cold Beer™ game is functioning correctly. After initial setup, perform these two tests: the Bar Test and the Hole Test. Bar Test : Verifies that the bar can travel across the entire…

Playfield Removal

MAINTENANCE » Playfield Removal

1. Remove top bar holding glass & remove glass 2. Remove 2 screws under marquee light or bolts & remove ball from gate 3. Remove back of game & unplug coin door, control panel & Power supply connectors 4. Remove wire clamp holding wiring harness to playfield …

Testing Hole No. 1

“ICE COLD BEER” GAME SET-UP » Initial Testing Procedures » Testing Hole No. 1

After you have tested the bar, place the ball onto the metal return at the bottom and allow it to roll into the return hole. The servo should return the ball to the gate. Select “LIVE VIEW” in the Ice Cold Beer app if you have not already done so. On…